Aktuelle Zeit: Di 27. Jun 2017, 14:17



Ein neues Thema erstellen Auf das Thema antworten  [ 126 Beiträge ]  Gehe zu Seite Vorherige  1 ... 9, 10, 11, 12, 13
 LS420D zur TS1200D umflashen 
Autor Nachricht
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 7 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
Hi oxygen8,

it's me again, and I have another "brainteaser" :roll:

I made the changes:

Code:
dumpnf > /tmp/nas_feature

sed -i 's/PID=0x0000300C/PID=0x0000300B/g' /tmp/nas_feature

sed -i 's/USB_TREE_TYPE=armada370-platform/USB_TREE_TYPE=/g' /tmp/nas_feature

sed -i 's/MAX_USBDISK_NUM=2/MAX_USBDISK_NUM=1/g' /tmp/nas_feature

sed -i 's/PRODUCT_CAPACITY=""/PRODUCT_CAPACITY="060"/g' /tmp/nas_feature

setnf < /tmp/nas_feature


After reboot, I flash NAS official firmware FW ver1.34

NAS work fine - LS420
Bild

After next change:

Code:
dumpnf > /tmp/nas_feature

sed -i 's/PID=0x0000300B/PID=0x00002025/g' /tmp/nas_feature

sed -i 's/NAS_FEATURE_VERSION=0.0.0/NAS_FEATURE_VERSION=3.0.0/g' /tmp/nas_feature

setnf < /tmp/nas_feature


After reboot and load via Serial Console (with TFTP boot recovery) initrd.buffalo and uImage.buffalo for TS1200
I flash firmware TerraStation FWver 1.41 with settings

Bild

Bild

Bild

After auto reboot, NAS not loaded.... kernel

Code:
BootROM 1.08
Booting from SPI flash


General initialization - Version: 1.0.0
mvBoardSerdesModulesScan: mvTwsiRead error, Using default serdes configuration *                                                                                                                                                             ***
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x67100
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1

DDR3 Training Sequence - Run DDR3 at 600 Mhz

########### LOG LEVEL 1 (D-UNIT SETUP)###########

Static D-UNIT Setup:
0x00001400 = 0x73014924
0x00001404 = 0x3000B808
0x00001408 = 0x56159996
0x0000140C = 0x3AD93F96
0x00001410 = 0x120F0000
0x00001414 = 0x00000000
0x00001418 = 0x00000E00
0x0000141C = 0x00000642
0x00001420 = 0x00000004
0x00001424 = 0x0100F37F
0x00001428 = 0x000F8830
0x00001454 = 0x00000000
0x00001474 = 0x00000000
0x0000142C = 0x014C4EE4
0x0000147C = 0x0000C671
0x00001494 = 0x00010000
0x00001498 = 0x00000000
0x0000149C = 0x0000030F
DDR3 Training Sequence - Run without PBS.
Cuurrent frequency is: 100MHz
Cuurrent frequency is: 444MHz
DDR3 - Write Leveling - Starting HW WL procedure
DDR3 - Write Leveling - Write Leveling Cs - 0 Results:
DDR3 - Write Leveling - PUP: 0, Phase: 0, Delay: 03
DDR3 - Write Leveling - PUP: 1, Phase: 0, Delay: 08
DDR3 - Write Leveling - HW WL Ended Successfully
DDR3 - Read Leveling - Starting HW RL procedure
DDR3 - Read Leveling - Results for CS - 0
DDR3 - Read Leveling - PUP: 0, Phase: 1, Delay: 1F
DDR3 - Read Leveling - PUP: 1, Phase: 2, Delay: 01
DDR3 - Read Leveling - Read Sample Delay: 09
DDR3 - Read Leveling - Read Ready Delay: 0D
DDR3 - Read Leveling - HW RL Ended Successfully
DDR3 - Write Leveling Hi-Freq Supplement - Starting
DDR3 - Write Leveling Hi-Freq Supplement - SW Override Enabled
COUNT = 0
DATA PUP:
04030201 08070605 0C0B0A09 100F0E0D
14131211 18171615 1C1B1A19 201F1E1D
24232221 28272625 2C2B2A29 302F2E2D
34333231 38373635 3C3B3A39 403F3E3D
44434241 48474645 4C4B4A49 504F4E4D
54535251 58575655 5C5B5A59 605F5E5D
64636261 68676665 6C6B6A69 706F6E6D
74737271 78777675 7C7B7A79 807F7E7D
CS: 0 PUP: 0
Actual Data = 21
Expected Data = 21
uiError = 00
uiErrorN = 00

CS: 0 PUP: 1
Actual Data = 22
Expected Data = 22
uiError = 00
uiErrorN = 00
COUNT = 1
DATA PUP:
04030201 08070605 0C0B0A09 100F0E0D
14131211 18171615 1C1B1A19 201F1E1D
24232221 28272625 2C2B2A29 302F2E2D
34333231 38373635 3C3B3A39 403F3E3D
44434241 48474645 4C4B4A49 504F4E4D
54535251 58575655 5C5B5A59 605F5E5D
64636261 68676665 6C6B6A69 706F6E6D
74737271 78777675 7C7B7A79 807F7E7D
CS: 0 PUP: 0
Actual Data = 21
Expected Data = 21
uiError = 00
uiErrorN = 00

CS: 0 PUP: 1
Actual Data = 22
Expected Data = 22
uiError = 00
uiErrorN = 00
DDR3 - Write Leveling Hi-Freq Supplement - Ended Successfully

########## LOG LEVEL 3(Windows margins per-DQ) ##########
DDR3 - RX  CS: 0

DATA RESULTS:

BYTE:0
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 0]     0x40       0x2D       0xEE
DQ[ 1]     0x33       0x2F       0xFD
DQ[ 2]     0xEA       0x4B       0x62
DQ[ 3]     0x01       0xF2       0xF2
DQ[ 4]     0x59       0xFE       0xA6
DQ[ 5]     0x9A       0xE5       0x4C
DQ[ 6]     0x6F       0xFF       0x91
DQ[ 7]     0x3B       0xAD       0x73

BYTE:1
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 8]     0x5D       0x9D       0x41
DQ[ 9]     0x4E       0x0D       0xC0
DQ[10]     0xC7       0x73       0xAD
DQ[11]     0x41       0xFF       0xBF
DQ[12]     0xE2       0x40       0x5F
DQ[13]     0x7A       0x86       0x0D
DQ[14]     0xFA       0xE7       0xEE
DQ[15]     0x20       0x08       0xE9


############ LOG LEVEL 2(Windows margins) ############
DDR3 - DQS RX - Set Dqs Centralization Results - CS: 0

DQS    LOW     HIGH     WIN-SIZE      Set
==============================================
0     0x00      0x1A      0x1A       0x0D
1     0x00      0x1B      0x1B       0x0D

########## LOG LEVEL 3(Windows margins per-DQ) ##########
DDR3 - TX  CS: 0

DATA RESULTS:

BYTE:0
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 0]      0x2E        0x40        0x12
DQ[ 1]      0x30        0x33        0x03
DQ[ 2]      0x4C        0xEA        0x9E
DQ[ 3]      0xF3        0x01        0x0E
DQ[ 4]      0xFF        0x59        0x5A
DQ[ 5]      0xE6        0x9A        0xB4
DQ[ 6]      0x00        0x6F        0x6F
DQ[ 7]      0xAE        0x3B        0x8D

BYTE:1
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 8]      0x9E        0x5D        0xBF
DQ[ 9]      0x0E        0x4E        0x40
DQ[10]      0x74        0xC7        0x53
DQ[11]      0x00        0x41        0x41
DQ[12]      0x41        0xE2        0xA1
DQ[13]      0x87        0x7A        0xF3
DQ[14]      0xE8        0xFA        0x12
DQ[15]      0x09        0x20        0x17


############ LOG LEVEL 2(Windows margins) ############
DDR3 - DQS TX - Set Dqs Centralization Results - CS: 0

DQS    LOW     HIGH     WIN-SIZE      Set
==============================================
0     0x00      0x1C      0x1C       0x0E
1     0x00      0x1B      0x1B       0x0D
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED

____                            _
| __ )  _   _  ___   ___   ___  | |  ___
|  _  \| | | |/   | /   | / _  \| | / _  \
| |_) || |_| ||  __||  __| (_) || || (_) |
|____/  \___/ |_|   |_|   \__/|||_| \___/
         _   _     ____                _
        | | | |   | __ )   ___   ___  | |_
        | | | |___|  _  \ / _  \/ _  \| __|
        | |_| |___| |_) || (_) | (_) || |_
         \___/    |____/  \___/ \___/  \__|
** LOADER **


U-Boot 2011.12 (Mar 04 2015 - 19:45:59) Marvell version: v2011.12 2014_T2.0p1

Board: YANAGI
BoardID= 0
SoC:   MV6710 A1
CPU:   Marvell PJ4B v7 UP (Rev 1) LE
       CPU    @ 1200 [MHz]
       L2     @ 600 [MHz]
       TClock @ 200 [MHz]
       DDR    @ 600 [MHz]
       DDR 16Bit Width, FastPath Memory Access
DRAM:  512 MiB
PHY ID = 1d
PHY ID = 1d

Map:   Code:            0x1ff0d000:0x1ffa2af8
       BSS:             0x1ffefaa4
       Stack:           0x1f9fcef8
       Heap:            0x1f9fd000:0x1ff0d000

NAND:  512 MiB
MMC:   MRVL_MMC: 0
SF: Detected MX25L8005 with page size 64 KiB, total 1 MiB

Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 1.1
PEX 0.1(1): Detected No Link.
u-boot envinit tval=f272604f
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
       RGMII0 Phy
       RGMII1 Phy
       PEX0 (Lane 0)
       PEX1 (Lane 1)
       SATA0 (Lane 2)
       SATA1 (Lane 3)
HDD0 Power ON
HDD1 Power ON
USB Power ON

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0 @ 0 0:
Model: WDC WD30PURX-64P6ZY0                     Firm: 80.00A80 Ser#:      WD-WCC4N7AL8UYZ
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
  Device 1 @ 0 1:
Model: WDC WD10EFRX-68JCSN0                     Firm: 01.01A01 Ser#:      WD-WCC1U2198392
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)

MAC Address : 10:6F:3F:XX:XX:XX
MAC Address read from block device 0 : 00:50:43:b4:cb:c6
Loading file "/initrd.buffalo" from ide device 0:1 (primary)
24435946 bytes read
MAC Address read from block device 1 : 00:50:43:b4:cb:c6
Loading file "/initrd.buffalo" from ide device 1:1 (primary)
24435946 bytes read
Booting from Device 0
Net:   egiga0, egiga1 [PRIME]
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  0
Loading file "/initrd.buffalo" from ide device 0:1 (primary)
24435946 bytes read
Loading file "/uImage.buffalo" from ide device 0:1 (primary)
3159144 bytes read
No SPI flash selected. Please run `sf probe'
## Booting kernel from Legacy Image at 01200000 ...
   Image Name:   Linux-3.3.4
   Created:      2016-03-31  11:12:54 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3159080 Bytes = 3 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02600000 ...
   Image Name:   initramfs.cpio
   Created:      2016-04-01   2:30:15 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    24435882 Bytes = 23.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...


Starting kernel ...

Uncompressing Linux... done, booting the kernel.


blinks white LED, so he stood for more than one hour.

If remove disks - blinks red signal (push Functional Button with TFTP), but after downloading images - similar situation.


Code:
BootROM 1.08
Booting from SPI flash


General initialization - Version: 1.0.0
mvBoardSerdesModulesScan: mvTwsiRead error, Using default serdes configuration ****
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x67100
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1

DDR3 Training Sequence - Run DDR3 at 600 Mhz

########### LOG LEVEL 1 (D-UNIT SETUP)###########

Static D-UNIT Setup:
0x00001400 = 0x73014924
0x00001404 = 0x3000B808
0x00001408 = 0x56159996
0x0000140C = 0x3AD93F96
0x00001410 = 0x120F0000
0x00001414 = 0x00000000
0x00001418 = 0x00000E00
0x0000141C = 0x00000642
0x00001420 = 0x00000004
0x00001424 = 0x0100F37F
0x00001428 = 0x000F8830
0x00001454 = 0x00000000
0x00001474 = 0x00000000
0x0000142C = 0x014C4EE4
0x0000147C = 0x0000C671
0x00001494 = 0x00010000
0x00001498 = 0x00000000
0x0000149C = 0x0000030F
DDR3 Training Sequence - Run without PBS.
Cuurrent frequency is: 100MHz
Cuurrent frequency is: 444MHz
DDR3 - Write Leveling - Starting HW WL procedure
DDR3 - Write Leveling - Write Leveling Cs - 0 Results:
DDR3 - Write Leveling - PUP: 0, Phase: 0, Delay: 03
DDR3 - Write Leveling - PUP: 1, Phase: 0, Delay: 08
DDR3 - Write Leveling - HW WL Ended Successfully
DDR3 - Read Leveling - Starting HW RL procedure
DDR3 - Read Leveling - Results for CS - 0
DDR3 - Read Leveling - PUP: 0, Phase: 2, Delay: 00
DDR3 - Read Leveling - PUP: 1, Phase: 2, Delay: 02
DDR3 - Read Leveling - Read Sample Delay: 09
DDR3 - Read Leveling - Read Ready Delay: 0D
DDR3 - Read Leveling - HW RL Ended Successfully
DDR3 - Write Leveling Hi-Freq Supplement - Starting
DDR3 - Write Leveling Hi-Freq Supplement - SW Override Enabled
COUNT = 0
DATA PUP:
04030201 08070605 0C0B0A09 100F0E0D
14131211 18171615 1C1B1A19 201F1E1D
24232221 28272625 2C2B2A29 302F2E2D
34333231 38373635 3C3B3A39 403F3E3D
44434241 48474645 4C4B4A49 504F4E4D
54535251 58575655 5C5B5A59 605F5E5D
64636261 68676665 6C6B6A69 706F6E6D
74737271 78777675 7C7B7A79 807F7E7D
CS: 0 PUP: 0
Actual Data = 21
Expected Data = 21
uiError = 00
uiErrorN = 00

CS: 0 PUP: 1
Actual Data = 22
Expected Data = 22
uiError = 00
uiErrorN = 00
COUNT = 1
DATA PUP:
04030201 08070605 0C0B0A09 100F0E0D
14131211 18171615 1C1B1A19 201F1E1D
24232221 28272625 2C2B2A29 302F2E2D
34333231 38373635 3C3B3A39 403F3E3D
44434241 48474645 4C4B4A49 504F4E4D
54535251 58575655 5C5B5A59 605F5E5D
64636261 68676665 6C6B6A69 706F6E6D
74737271 78777675 7C7B7A79 807F7E7D
CS: 0 PUP: 0
Actual Data = 21
Expected Data = 21
uiError = 00
uiErrorN = 00

CS: 0 PUP: 1
Actual Data = 22
Expected Data = 22
uiError = 00
uiErrorN = 00
DDR3 - Write Leveling Hi-Freq Supplement - Ended Successfully

########## LOG LEVEL 3(Windows margins per-DQ) ##########
DDR3 - RX  CS: 0

DATA RESULTS:

BYTE:0
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 0]     0x40       0x2D       0xEE
DQ[ 1]     0x33       0x2F       0xFD
DQ[ 2]     0xE8       0x4B       0x64
DQ[ 3]     0x01       0xFA       0xFA
DQ[ 4]     0x99       0xF6       0x5E
DQ[ 5]     0xBA       0xF5       0x3C
DQ[ 6]     0x6F       0x01       0x93
DQ[ 7]     0x3B       0xAD       0x73

BYTE:1
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 8]     0x5D       0x9D       0x41
DQ[ 9]     0x4E       0x0D       0xC0
DQ[10]     0xC7       0x75       0xAF
DQ[11]     0x41       0x01       0xC1
DQ[12]     0xE2       0x40       0x5F
DQ[13]     0x7A       0x84       0x0B
DQ[14]     0xFA       0xC7       0xCE
DQ[15]     0x20       0x08       0xE9


############ LOG LEVEL 2(Windows margins) ############
DDR3 - DQS RX - Set Dqs Centralization Results - CS: 0

DQS    LOW     HIGH     WIN-SIZE      Set
==============================================
0     0x00      0x1A      0x1A       0x0D
1     0x00      0x1B      0x1B       0x0D

########## LOG LEVEL 3(Windows margins per-DQ) ##########
DDR3 - TX  CS: 0

DATA RESULTS:

BYTE:0
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 0]      0x2E        0x40        0x12
DQ[ 1]      0x30        0x33        0x03
DQ[ 2]      0x4C        0xE8        0x9C
DQ[ 3]      0xFB        0x01        0x06
DQ[ 4]      0xF7        0x99        0xA2
DQ[ 5]      0xF6        0xBA        0xC4
DQ[ 6]      0x02        0x6F        0x6D
DQ[ 7]      0xAE        0x3B        0x8D

BYTE:1
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 8]      0x9E        0x5D        0xBF
DQ[ 9]      0x0E        0x4E        0x40
DQ[10]      0x76        0xC7        0x51
DQ[11]      0x02        0x41        0x3F
DQ[12]      0x41        0xE2        0xA1
DQ[13]      0x85        0x7A        0xF5
DQ[14]      0xC8        0xFA        0x32
DQ[15]      0x09        0x20        0x17


############ LOG LEVEL 2(Windows margins) ############
DDR3 - DQS TX - Set Dqs Centralization Results - CS: 0

DQS    LOW     HIGH     WIN-SIZE      Set
==============================================
0     0x00      0x1B      0x1B       0x0D
1     0x00      0x1C      0x1C       0x0E
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED

____                            _
| __ )  _   _  ___   ___   ___  | |  ___
|  _  \| | | |/   | /   | / _  \| | / _  \
| |_) || |_| ||  __||  __| (_) || || (_) |
|____/  \___/ |_|   |_|   \__/|||_| \___/
         _   _     ____                _
        | | | |   | __ )   ___   ___  | |_
        | | | |___|  _  \ / _  \/ _  \| __|
        | |_| |___| |_) || (_) | (_) || |_
         \___/    |____/  \___/ \___/  \__|
** LOADER **


U-Boot 2011.12 (Mar 04 2015 - 19:45:59) Marvell version: v2011.12 2014_T2.0p1

Board: YANAGI
BoardID= 0
SoC:   MV6710 A1
CPU:   Marvell PJ4B v7 UP (Rev 1) LE
       CPU    @ 1200 [MHz]
       L2     @ 600 [MHz]
       TClock @ 200 [MHz]
       DDR    @ 600 [MHz]
       DDR 16Bit Width, FastPath Memory Access
DRAM:  512 MiB
PHY ID = 1d
PHY ID = 1d

Map:   Code:            0x1ff0d000:0x1ffa2af8
       BSS:             0x1ffefaa4
       Stack:           0x1f9fcef8
       Heap:            0x1f9fd000:0x1ff0d000

NAND:  512 MiB
MMC:   MRVL_MMC: 0
SF: Detected MX25L8005 with page size 64 KiB, total 1 MiB

Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 1.1
PEX 0.1(1): Detected No Link.
u-boot envinit tval=f2726b83
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
       RGMII0 Phy
       RGMII1 Phy
       PEX0 (Lane 0)
       PEX1 (Lane 1)
       SATA0 (Lane 2)
       SATA1 (Lane 3)
USB Power ON

Marvell Serial ATA Adapter
Integrated Sata device found

MAC Address : 10:6F:3F:XX:XX:XX
Net:   egiga0, egiga1 [PRIME]
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  0
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000002000000 : "mtd=0"
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: Bad block at 0x000001c40000
nand_read_bbt: Bad block at 0x000001c60000
nand_read_bbt: Bad block at 0x000003fa0000
nand_read_bbt: Bad block at 0x000006080000
nand_read_bbt: Bad block at 0x0000060a0000
nand_read_bbt: Bad block at 0x000008ac0000
nand_read_bbt: Bad block at 0x00000b800000
nand_read_bbt: Bad block at 0x00000efa0000
nand_read_bbt: Bad block at 0x00001a480000
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI error: ubi_read_volume_table: the layout volume was not found
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -22
UBI init error 22
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:boot", error -19
Error reading superblock on volume 'ubi:boot'!
ubifsmount - mount UBIFS volume

Usage:
ubifsmount <volume-name>
    - mount 'volume-name' volume
UBIFS not mounted, use ubifs mount to mount volume first!
ubifsload - load file from an UBIFS filesystem

Usage:
ubifsload <addr> <filename> [bytes]
    - load file 'filename' to address 'addr'
UBIFS not mounted, use ubifs mount to mount volume first!
ubifsload - load file from an UBIFS filesystem

Usage:
ubifsload <addr> <filename> [bytes]
    - load file 'filename' to address 'addr'
No SPI flash selected. Please run `sf probe'
Wrong Image Format for bootm command
ERROR: can't get kernel image!
(Re)start USB...
USB:   Active port:     0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found

** Invalid boot device **

** Invalid boot device **

** Invalid boot device **

** Invalid boot device **
No SPI flash selected. Please run `sf probe'
Wrong Image Format for bootm command
ERROR: can't get kernel image!
*** booting failed. press func sw to continue
egiga1 wait for link .Done - link up.
Using egiga1 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'uImage.buffalo'.
Load address: 0x1200000
Loading: #################################################################
         #################################################################
         #################################################################
         #####################
done
Bytes transferred = 3159104 (303440 hex)
Using egiga1 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'initrd.buffalo'.
Load address: 0x2600000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #########################################
done
Bytes transferred = 24448120 (1750c78 hex)
No SPI flash selected. Please run `sf probe'
## Booting kernel from Legacy Image at 01200000 ...
   Image Name:   Linux-3.3.4
   Created:      2015-08-31   7:04:30 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3159040 Bytes = 3 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02600000 ...
   Image Name:   initramfs.cpio
   Created:      2015-09-08   7:55:22 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    24448056 Bytes = 23.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...


Starting kernel ...

Uncompressing Linux... done, booting the kernel.


available commands
Code:
BUFFALO>> help
?       - alias for 'help'
SatR    - Sample At Reset sub-system

active_units- print Board units active
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootfail- - boot image not found. press func sw to continue .

bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
bootvx  - Boot vxWorks from an ELF image
bootz   - boot Linux zImage image from memory
bubt    - bubt  - Burn an image on the Boot Flash.

chpart  - change active partition
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
date    - get/set/reset date & time
dcache  - enable or disable data cache
ddrPhyRead- ddrPhyRead - Read DDR PHY register

ddrPhyWrite- ddrPhyWrite - Write DDR PHY register

dhcp    - boot image via network using DHCP/TFTP protocol
diskboot- diskboot- boot from IDE device

dma     - dma   - Perform DMA using the XOR engine

echo    - echo args to console
editenv - edit environment variable
eeprom  - EEPROM sub-system
env     - environment handling commands
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false   - do nothing, unsuccessfully
fatIsSettingInitializeDisk- Check if it is a setting initialize disk or not.
fatIsSettingRecoveryDisk- Check if it is a setting recovery disk or not.
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fsinfo  - print information about filesystems
fsload  - load binary file from a filesystem image
go      - start application at address 'addr'
help    - print command description/usage
i2c     - I2C sub-system
icache  - enable or disable instruction cache
ide     - ide     - IDE sub-system

iminfo  - print header information for application image
imxtract- extract a part of a multi-image
ir      - ir    - reading and changing MV internal register values.

itest   - return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
ls      - list files in a directory (default /)
map     - map   - Display address decode windows

md      - memory display
me      - me    - PCI master enable

mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
mp      - mp    - map PCI BAR

mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nfs     - boot image via network using NFS protocol
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
pciePhyRead- phyRead    - Read PCI-E Phy register

pciePhyWrite- pciePhyWrite      - Write PCI-E Phy register

phyRead - phyRead       - Read Phy register

phyWrite- phyWrite      - Write Phy register

ping    - send ICMP ECHO_REQUEST to network host
poff    - - Board power off

printenv- print environment variables
pxe     - commands to get and boot from pxe files
rcvr    - rcvr  - Satrt recovery process (Distress Beacon with TFTP server)

reboot  - - Board power off

reset   - Perform RESET of the CPU
resetenv- resetenv      - Erase environment sector to reset all variables to default.

run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
se      - se    - PCI Slave enable

setenv  - set environment variables
sf      - SPI flash sub-system
sg      - sg    - scanning the PHYs status

showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
sp      - scan and detect all devices on mvPCI interface
sspi    - SPI utility command
sum_check_nand- - nand checksum checking now by spi env... .

temp    - temp  - Display the device temperature.

tempCmd0- tempCmd - This command allocated for monitor extinction

tempCmd1- tempCmd - This command allocated for monitor extinction

tempCmd2- tempCmd - This command allocated for monitor extinction

tempCmd3- tempCmd - This command allocated for monitor extinction

test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
training- training      - prints the results of the DDR3 Training.

true    - do nothing, successfully
ts_report- ts_report    - report touch screen coordinate

ts_test - ts_test       - test touch screen

ubi     - ubi commands
ubifsload- load file from an UBIFS filesystem
ubifsls - list files in a directory
ubifsmount- mount UBIFS volume
ubifsumount- unmount UBIFS volume
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
whoAmI  - - reading CPU ID

BUFFALO>> 


If I understand correctly, the problem is u-Boot, I think that to boot kernel, need u-Boot by ls400 series.
Then can use this command:

bubt    - bubt  - Burn an image on the Boot Flash.

Code:
BUFFALO>> bubt
Using default filename "u-boot.bin"
SF: Detected MX25L8005 with page size 64 KiB, total 1 MiB
egiga1 wait for link .Done - link up.
Using egiga1 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'u-boot.bin'.
Load address: 0x2000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Checking file size:             [ERR!]
BUFFALO>


I do not know where to get / unzip this file from an image :?

Please help me :idea:


Zuletzt geändert von Antonas am Mo 20. Feb 2017, 07:59, insgesamt 1-mal geändert.



Mo 20. Feb 2017, 06:52
Profil
Dieser Werbeblock wird nur bei Gästen angezeigt
Globaler Moderator

Registriert: Mo 5. Apr 2010, 23:32
Beiträge: 6185
Bilder: 333

Bedankte sich: 173 mal
Erhielt: 796 Danksagungen in 736 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
Ich kann dir dabei nicht helfen.

Ich würde den Bootloader nicht ändern und ich hatte dir empfohlen, deine 421 nicht mit der Software für die 420 zu betreiben.

Bitte mach was du willst, lass mich da aber raus.


Mo 20. Feb 2017, 07:56
Profil Persönliches Album 
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 7 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
oxygen8 hat geschrieben:
Ich kann dir dabei nicht helfen.

Ich würde den Bootloader nicht ändern und ich hatte dir empfohlen, deine 421 nicht mit der Software für die 420 zu betreiben.

Bitte mach was du willst, lass mich da aber raus.

He has flashed like TS1200 :roll:

where to get file u-boot.bin for LS400 series?

UPD I unzip u-boot.img and rename u-boot-ls400.buffalo.updated to u-boot.bin

Flash via TFTP

Code:
BUFFALO>> bubt
Using default filename "u-boot.bin"
SF: Detected MX25L8005 with page size 64 KiB, total 1 MiB
egiga1 wait for link .Done - link up.
Using egiga1 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'u-boot.bin'.
Load address: 0x2000000
Loading: ###################################################
done
Bytes transferred = 744892 (b5dbc hex)
Checking file size:             [Done]
Override Env parameters to default? [y/N]


I chose - N

Code:
Erasing 0x0 - 0xf0000: ........         [Done]
Writing image to flash:......................           [Done]
BUFFALO>>


start boot

Code:
BUFFALO>>boot
Loading file "/initrd.buffalo" from ide device 0:1 (primary)
24435946 bytes read
Loading file "/uImage.buffalo" from ide device 0:1 (primary)
3159144 bytes read
No SPI flash selected. Please run `sf probe'
## Booting kernel from Legacy Image at 01200000 ...
   Image Name:   Linux-3.3.4
   Created:      2016-03-31  11:12:54 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3159080 Bytes = 3 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02600000 ...
   Image Name:   initramfs.cpio
   Created:      2016-04-01   2:30:15 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    24435882 Bytes = 23.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...


Starting kernel ...

Uncompressing Linux... done, booting the kernel.


kernel not boot again..... may select - Y?


Mo 20. Feb 2017, 08:33
Profil
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 7 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
oxygen8 hat geschrieben:
Ich kann dir dabei nicht helfen.

Ich würde den Bootloader nicht ändern und ich hatte dir empfohlen, deine 421 nicht mit der Software für die 420 zu betreiben.

Bitte mach was du willst, lass mich da aber raus.


After reboot kernel booting and NAS appeared in network!


Code:
BootROM 1.08
Booting from SPI flash


General initialization - Version: 1.0.0
mvBoardSerdesModulesScan: mvTwsiRead error, Using default serdes configuration *                                                                                                                                                             ***
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x67100
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1

DDR3 Training Sequence - Run DDR3 at 600 Mhz

########### LOG LEVEL 1 (D-UNIT SETUP)###########

Static D-UNIT Setup:
0x00001400 = 0x73014924
0x00001404 = 0x3000B808
0x00001408 = 0x56159996
0x0000140C = 0x3AD93F96
0x00001410 = 0x120F0000
0x00001414 = 0x00000000
0x00001418 = 0x00000E00
0x0000141C = 0x00000642
0x00001420 = 0x00000004
0x00001424 = 0x0100F37F
0x00001428 = 0x000F8830
0x00001454 = 0x00000000
0x00001474 = 0x00000000
0x0000142C = 0x014C4EE4
0x0000147C = 0x0000C671
0x00001494 = 0x00010000
0x00001498 = 0x00000000
0x0000149C = 0x0000030F
DDR3 Training Sequence - Run without PBS.
Cuurrent frequency is: 100MHz
Cuurrent frequency is: 444MHz
DDR3 - Write Leveling - Starting HW WL procedure
DDR3 - Write Leveling - Write Leveling Cs - 0 Results:
DDR3 - Write Leveling - PUP: 0, Phase: 0, Delay: 03
DDR3 - Write Leveling - PUP: 1, Phase: 0, Delay: 07
DDR3 - Write Leveling - HW WL Ended Successfully
DDR3 - Read Leveling - Starting HW RL procedure
DDR3 - Read Leveling - Results for CS - 0
DDR3 - Read Leveling - PUP: 0, Phase: 1, Delay: 1F
DDR3 - Read Leveling - PUP: 1, Phase: 2, Delay: 02
DDR3 - Read Leveling - Read Sample Delay: 09
DDR3 - Read Leveling - Read Ready Delay: 0D
DDR3 - Read Leveling - HW RL Ended Successfully
DDR3 - Write Leveling Hi-Freq Supplement - Starting
DDR3 - Write Leveling Hi-Freq Supplement - SW Override Enabled
COUNT = 0
DATA PUP:
04030201 08070605 0C0B0A09 100F0E0D
14131211 18171615 1C1B1A19 201F1E1D
24232221 28272625 2C2B2A29 302F2E2D
34333231 38373635 3C3B3A39 403F3E3D
44434241 48474645 4C4B4A49 504F4E4D
54535251 58575655 5C5B5A59 605F5E5D
64636261 68676665 6C6B6A69 706F6E6D
74737271 78777675 7C7B7A79 807F7E7D
CS: 0 PUP: 0
Actual Data = 21
Expected Data = 21
uiError = 00
uiErrorN = 00

CS: 0 PUP: 1
Actual Data = 22
Expected Data = 22
uiError = 00
uiErrorN = 00
COUNT = 1
DATA PUP:
04030201 08070605 0C0B0A09 100F0E0D
14131211 18171615 1C1B1A19 201F1E1D
24232221 28272625 2C2B2A29 302F2E2D
34333231 38373635 3C3B3A39 403F3E3D
44434241 48474645 4C4B4A49 504F4E4D
54535251 58575655 5C5B5A59 605F5E5D
64636261 68676665 6C6B6A69 706F6E6D
74737271 78777675 7C7B7A79 807F7E7D
CS: 0 PUP: 0
Actual Data = 21
Expected Data = 21
uiError = 00
uiErrorN = 00

CS: 0 PUP: 1
Actual Data = 22
Expected Data = 22
uiError = 00
uiErrorN = 00
DDR3 - Write Leveling Hi-Freq Supplement - Ended Successfully

########## LOG LEVEL 3(Windows margins per-DQ) ##########
DDR3 - RX  CS: 0

DATA RESULTS:

BYTE:0
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 0]     0x51       0x2D       0xDD
DQ[ 1]     0x33       0x2F       0xFD
DQ[ 2]     0xEA       0x4B       0x62
DQ[ 3]     0x01       0xFA       0xFA
DQ[ 4]     0x59       0xFE       0xA6
DQ[ 5]     0x9A       0xF5       0x5C
DQ[ 6]     0x6F       0xFF       0x91
DQ[ 7]     0x3B       0xAD       0x73

BYTE:1
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 8]     0x5D       0x9D       0x41
DQ[ 9]     0x4E       0x0D       0xC0
DQ[10]     0xC7       0x75       0xAF
DQ[11]     0x41       0xFF       0xBF
DQ[12]     0xE2       0x40       0x5F
DQ[13]     0x7A       0x84       0x0B
DQ[14]     0xFA       0xEB       0xF2
DQ[15]     0x20       0x08       0xE9


############ LOG LEVEL 2(Windows margins) ############
DDR3 - DQS RX - Set Dqs Centralization Results - CS: 0

DQS    LOW     HIGH     WIN-SIZE      Set
==============================================
0     0x00      0x1A      0x1A       0x0D
1     0x00      0x1B      0x1B       0x0D

########## LOG LEVEL 3(Windows margins per-DQ) ##########
DDR3 - TX  CS: 0

DATA RESULTS:

BYTE:0
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 0]      0x2E        0x51        0x23
DQ[ 1]      0x30        0x33        0x03
DQ[ 2]      0x4C        0xEA        0x9E
DQ[ 3]      0xFB        0x01        0x06
DQ[ 4]      0xFF        0x59        0x5A
DQ[ 5]      0xF6        0x9A        0xA4
DQ[ 6]      0x00        0x6F        0x6F
DQ[ 7]      0xAE        0x3B        0x8D

BYTE:1
  DQ's        LOW       HIGH       WIN-SIZE
============================================
DQ[ 8]      0x9E        0x5D        0xBF
DQ[ 9]      0x0E        0x4E        0x40
DQ[10]      0x76        0xC7        0x51
DQ[11]      0x00        0x41        0x41
DQ[12]      0x41        0xE2        0xA1
DQ[13]      0x85        0x7A        0xF5
DQ[14]      0xEC        0xFA        0x0E
DQ[15]      0x09        0x20        0x17


############ LOG LEVEL 2(Windows margins) ############
DDR3 - DQS TX - Set Dqs Centralization Results - CS: 0

DQS    LOW     HIGH     WIN-SIZE      Set
==============================================
0     0x00      0x1C      0x1C       0x0E
1     0x00      0x1B      0x1B       0x0D
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED

____                            _
| __ )  _   _  ___   ___   ___  | |  ___
|  _  \| | | |/   | /   | / _  \| | / _  \
| |_) || |_| ||  __||  __| (_) || || (_) |
|____/  \___/ |_|   |_|   \__/|||_| \___/
         _   _     ____                _
        | | | |   | __ )   ___   ___  | |_
        | | | |___|  _  \ / _  \/ _  \| __|
        | |_| |___| |_) || (_) | (_) || |_
         \___/    |____/  \___/ \___/  \__|
** LOADER **


U-Boot 2011.12 (Jan 15 2015 - 21:22:47) Marvell version: v2011.12 2014_T2.0p1

Board: YANAGI
BoardID= 0
SoC:   MV6710 A1
CPU:   Marvell PJ4B v7 UP (Rev 1) LE
       CPU    @ 1200 [MHz]
       L2     @ 600 [MHz]
       TClock @ 200 [MHz]
       DDR    @ 600 [MHz]
       DDR 16Bit Width, FastPath Memory Access
DRAM:  512 MiB
PHY ID = 1d
PHY ID = 1d

Map:   Code:            0x1ff0d000:0x1ffa2b68
       BSS:             0x1ffefaa4
       Stack:           0x1f9fcef8
       Heap:            0x1f9fd000:0x1ff0d000

NAND:  512 MiB
MMC:   MRVL_MMC: 0
SF: Detected MX25L8005 with page size 64 KiB, total 1 MiB

Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 1.1
PEX 0.1(1): Detected No Link.
u-boot envinit tval=f271ce29
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
       RGMII0 Phy
       RGMII1 Phy
       PEX0 (Lane 0)
       PEX1 (Lane 1)
       SATA0 (Lane 2)
       SATA1 (Lane 3)
HDD0 Power ON
HDD1 Power ON
USB Power ON

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0 @ 0 0:
Model: WDC WD30PURX-64P6ZY0                     Firm: 80.00A80 Ser#:      WD-WCC4N7AL8UYZ
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
  Device 1 @ 0 1:
Model: WDC WD10EFRX-68JCSN0                     Firm: 01.01A01 Ser#:      WD-WCC1U2198392
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)

MAC Address : 10:6F:3F:xx:xx:xx
MAC Address read from block device 0 : 00:50:43:b4:cb:c6
Loading file "/initrd.buffalo" from ide device 0:1 (primary)
24435946 bytes read
MAC Address read from block device 1 : 00:50:43:b4:cb:c6
Loading file "/initrd.buffalo" from ide device 1:1 (primary)
24435946 bytes read
Booting from Device 0
Net:   egiga0, egiga1 [PRIME]
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  0
Loading file "/initrd.buffalo" from ide device 0:1 (primary)
24435946 bytes read
Loading file "/uImage.buffalo" from ide device 0:1 (primary)
3159144 bytes read
No SPI flash selected. Please run `sf probe'
## Booting kernel from Legacy Image at 01200000 ...
   Image Name:   Linux-3.3.4
   Created:      2016-03-31  11:12:54 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3159080 Bytes = 3 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02600000 ...
   Image Name:   initramfs.cpio
   Created:      2016-04-01   2:30:15 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    24435882 Bytes = 23.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...


Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0
Initializing cgroup subsys cpu
Linux version 3.3.4 (root@buildsrv-Debian7) (gcc version 4.6.2 (Linaro GCC branch-4.6.2. Marvell GCC 201201-883.01c949de) ) #1 Thu Mar 31 20:12:49 JST 2016
CPU: Marvell PJ4Bv7 Processor [561f5811] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
Machine: Marvell Armada-370
Using UBoot passing parameters structure
>>>>>>>Tag MAC ce:29:71:43:50:00
>>>>>>>Tag MAC 4c:13:cd:3f:6f:10
Memory policy: ECC disabled, Data cache writealloc
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/nfs rw BOOTVER=0.16 UBOOT_DATE=2015/01/15 mtdparts=armada-nand:0x2000000(boot),0x1e000000(rootfs)
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 485328k/485328k available, 38960k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc05b5bb4   (5815 kB)
      .init : 0xc05b6000 - 0xc05dc000   ( 152 kB)
      .data : 0xc05dc000 - 0xc060f720   ( 206 kB)
       .bss : 0xc060f744 - 0xc064d5f8   ( 248 kB)
NR_IRQS:256
axp_time_init
Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
hw perfevents: no hardware support available
Setting up static identity map for 0x43ddb8 - 0x43ddfc
devtmpfs: initialized
xor: measuring software checksum speed
   arm4regs  :  1151.600 MB/sec
   8regs     :   816.800 MB/sec
   32regs    :  1149.600 MB/sec
xor: using function: arm4regs (1151.600 MB/sec)
NET: Registered protocol family 16
L0 cache Enabled
Speculative Prefetch Disabled
aurora_l2_init
Aurora: Enabling L2
AuroraL2: System L2 cache support initialised
Support IO coherency.
Enable DLB and DRAM write coalescing

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 512MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
DEVICE_CS0 ....base f2000000, size  32MB
DEVICE_CS1 ....no such
DEVICE_CS2 ....no such
DEVICE_CS3 ....no such
PEX0_MEM ....base e0000000, size  32MB
PEX0_IO ....base f1100000, size   1MB
PEX1_MEM ....base e2000000, size  32MB
PEX1_IO ....base f1200000, size   1MB
INTER_REGS ....base d0000000, size   1MB
DMA_UART ....no such
SPI_CS0 ....base f0000000, size  16MB
SPI_CS1 ....no such
SPI_CS2 ....no such
SPI_CS3 ....no such
SPI_CS4 ....no such
SPI_CS5 ....no such
SPI_CS6 ....no such
SPI_CS7 ....no such
BOOT_ROM_CS ....no such
DEV_BOOTCS ....base f5000000, size  16MB
PMU_SCRATCHPAD ....no such
CRYPT0_ENG ....base c8010000, size  64KB

  Marvell Armada370 Board-- YANAGI  Soc: MV6710 A1 LE
  LSP version: Armada370_LSP_3.1.0_p15_NQ


Detected Tclk 200000000, SysClk 600000000, FabricClk 600000000
gpiochip_add: registered GPIOs 0 to 64 on device: mv_gpio
hw-breakpoint: debug architecture 0x4 unsupported.
Marvell USB EHCI Host controller #0: d0052e80
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io  0x0000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe1ffffff]
PCI: bus0: Fast back to back transfers disabled
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io  0x100000-0x1fffff]
pci_bus 0000:01: root bus resource [mem 0xe2000000-0xe3ffffff]
PCI: bus1: Fast back to back transfers enabled
pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit]
bio: create slab <bio-0> at 0
raid6: int32x1    135 MB/s
raid6: int32x2    210 MB/s
raid6: int32x4    203 MB/s
raid6: int32x8    244 MB/s
raid6: using algorithm int32x8 (244 MB/s)
vgaarb: loaded
SCSI subsystem initialized
Switching to clocksource armada370_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 23860K
cesadev_init(c05bdc40)
mvCesaInit: channels=1, session=640, queue=64
Armada XP hwmon thermal sensor initialized.
Initializing Armada-XP CPU power management  (DISABLED)
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
initial_polarity_val = 0x0001f800
initial_polarity_val_high = 0x00000000
Buffalo GPIO SATA Hotplug Event Driver (C) BUFFALO INC. Ver.1.00 installed.-Polling mode-
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 994
async_tx: api initialized (async)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Initializing ths8200_init
Initializing dove_adi9889_init
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor )
mv_xor mv_xor.1: Marvell XOR: ( xor )
mv_xor mv_xor.2: Marvell XOR: ( cpy )
mv_xor mv_xor.3: Marvell XOR: ( fill cpy )
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xd0012000 (irq = 41) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
** BUFFALO Disable Command Queuing Function [sata_mv sata_mv.0] **
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 55
ata2: SATA max UDMA/133 irq 55
SPI Serial flash detected @ 0xf0000000, 1024KB (16sec x 64KB)
armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: bad block at 0x000001c40000
nand_read_bbt: bad block at 0x000001c60000
nand_read_bbt: bad block at 0x000003fa0000
nand_read_bbt: bad block at 0x000006080000
nand_read_bbt: bad block at 0x0000060a0000
nand_read_bbt: bad block at 0x000008ac0000
nand_read_bbt: bad block at 0x00000b800000
nand_read_bbt: bad block at 0x00000efa0000
nand_read_bbt: bad block at 0x00001a480000
2 cmdlinepart partitions found on MTD device armada-nand
Creating 2 MTD partitions on "armada-nand":
0x000000000000-0x000002000000 : "boot"
0x000002000000-0x000020000000 : "rootfs"
mv_eth_probe: port_mask=0x3, cpu_mask=0x1
0 - Base 0x00000000 , Size = 0x20000000.
4 - Base 0xf2000000 , Size = 0x02000000.
8 - Base 0xe0000000 , Size = 0x02000000.
9 - Base 0xf1100000 , Size = 0x00100000.
10 - Base 0xe2000000 , Size = 0x02000000.
11 - Base 0xf1200000 , Size = 0x00100000.
12 - Base 0xd0000000 , Size = 0x00100000.
14 - Base 0xf0000000 , Size = 0x01000000.
23 - Base 0xf5000000 , Size = 0x01000000.
25 - Base 0xc8010000 , Size = 0x00010000.
  o 2 Giga ports supported
  o NETA acceleration mode 1
  o RX Queue support: 1 Queues * 128 Descriptors
  o TX Queue support: 1 Queues * 512 Descriptors
  o GSO supported
  o GRO supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Driver ERROR statistics enabled
  o Switch support enabled

  o Loading network interface(s)

  o Port 0 is connected to Linux netdevice
        giga p=0: mtu=1500, mac=d002beec
    o eth0, ifindex = 2, GbE port = 0

  o Port 1 is connected to Linux netdevice
        giga p=1: mtu=1500, mac=d002beec
    o eth1, ifindex = 3, GbE port = 1

i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: create wakealarm
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
TCP cubic registered
NET: Registered protocol family 17
Registering the dns_resolver key type
VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
rtc-rs5c372 0-0032: setting system clock to 2017-02-19 14:50:00 UTC (1487515800)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
ata1.00: ATA-9: WDC WD30PURX-64P6ZY0, 80.00A80, max UDMA/133
ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD30PURX-64P 80.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 sda5 sda6
sd 0:0:0:0: [sda] Attached SCSI disk
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
ata2.00: ATA-8: WDC WD10EFRX-68JCSN0, 01.01A01, max UDMA/133
ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      WDC WD10EFRX-68J 01.0 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 1:0:0:0: [sdb] 4096-byte physical blocks
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6
sd 1:0:0:0: [sdb] Attached SCSI disk
Freeing init memory: 152K
0 /proc/sys/kernel/printk
Setup micon system...
/usr/local/lib/libsys: line 280: echo: write error: Input/output error
err: RecvPacket: readlen=0.
====== Entering initramfs(/init) ======
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
CANDIDATE_NUM=0 : CANDIDATE_LIST=
Selecting disk with not considering signature
CANDIDATE_NUM=2 : CANDIDATE_LIST=disk1 disk2
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda1): mounted filesystem with writeback data mode
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sdb1): mounted filesystem with writeback data mode
DISK=
err: RecvPacket: readlen=0.
libsys: nas_feature : using /root/.nas_features/EU/0x00002025
Checking the existance of micon ...
err: RecvPacket: readlen=0.
libsys: /etc/sysctl.conf : using /root/.params/sysctl/0x00002025
cp: can't stat '/root/.params/sysctl/0x00002025.iSCSI': No such file or directory
ls: /dev/rtc: No such file or directory
libsys: /dev/rtc was updated : /dev/rtc 254 0
Sun Feb 19 23:50:28 2017  -0.990409 seconds
Sun Feb 19 23:50:28 JST 2017
err: RecvPacket: readlen=0.
LibSys_GetUsbDiskStartNum : Usb device not found(/sys/block/sdc/device). Returning 3
grep: /var/tmp/devlink: No such file or directory
create_devlink:Using new routine.
grep: /var/tmp/devlink.bak: No such file or directory
Can't open /var/tmp/devlink.bak: No such file or directory.
Can't open /var/tmp/devlink.bak: No such file or directory.
console
root
BOOTVER
UBOOT_DATE
mtdparts
linuxrc:choose operation (timeout 4[s])
1:RamRoot 2:NfsRoot 3:sda1 4:sda2 other:HddRoot  ? -HddRoot-
CRC region is good. Continue boot process.
-- rebuild mdadm.conf for BOOT, ROOTFS with Intelligent routine --
checkDiskStatus : disk1 plugged
checkDiskStatus : disk1 LibSys_IsScsiDeviceExist [1] 0:0:0:0
checkDiskStatus : disk2 plugged
checkDiskStatus : disk2 LibSys_IsScsiDeviceExist [1] 1:0:0:0
checkDiskPerformanceParallel : Waiting for performance check will be done(timeout=20).
checkDiskPerformanceParallel : Disk which has performance lower than 30 MB/s will be kicked out.
checkDiskPerformanceParallel : disk1 plugged
checkDiskPerformanceParallel : disk2 plugged
checkDiskPerformanceParallel : disk1 performans test ... 90407 kB/s [OK]
checkDiskPerformanceParallel : disk2 performans test ... 74037 kB/s [OK]
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda1): mounted filesystem with writeback data mode
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sdb1): mounted filesystem with writeback data mode
libmd: GetMdBaseDisk : Selected 0
mdadm: cannot open /dev/disk??_1: No such file or directory
mdadm: cannot open /dev/disk??_2: No such file or directory
mdadm: cannot open /dev/disk??_5: No such file or directory
mdadm main: failed to get exclusive lock on mapfile
/sbin/hotplug [bdi]
md: md2 stopped.
/sbin/hotplug [block]
md: bind<sdb5>
md: bind<sda5>
bio: create slab <bio-1> at 1
md/raid1:md2: active with 2 out of 2 mirrors
created bitmap (1 pages) for device md2
md2: bitmap initialized from disk: read 1/1 pages, set 0 of 16 bits
/sbin/hotplug [block]
md2: detected capacity change from 0 to 1023410176
mdadm: /dev/md/2 has been started with 2 drives.
/sbin/hotplug [block]
md: md1 stopped.
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
md: bind<sdb2>
md: bind<sda2>
md/raid1:md1: active with 2 out of 2 mirrors
created bitmap (1 pages) for device md1
md1: bitmap initialized from disk: read 1/1 pages, set 0 of 77 bits
md1: detected capacity change from 0 to 5114888192
mdadm: /dev/md/1 has been started with 2 drives.
/sbin/hotplug [block]
md: md0 stopped.
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
md: bind<sdb1>
md: bind<sda1>
md/raid1:md0: active with 2 out of 2 mirrors
created bitmap (1 pages) for device md0
md0: bitmap initialized from disk: read 1/1 pages, set 0 of 16 bits
md0: detected capacity change from 0 to 1023868928
mdadm: /dev/md0 has been started with 2 drives.
-- setup max error counts --
/sbin/hotplug [block]
/sys/block/md0/md/maxerr_cnt is setted to 1000
/sys/block/md1/md/maxerr_cnt is setted to 1000
/sys/block/md2/md/maxerr_cnt is setted to 1000
Starting :fsck_disks(boot) ...         [Failed. ]
Starting :mount(boot) ...              mkdir: can't create directory '/boot': File exists
md0: unknown partition table
kjournald starting.  Commit interval 5 seconds
EXT3-fs (md0): using internal journal
EXT3-fs (md0): mounted filesystem with writeback data mode
[Success.]
Starting :umount(boot) ...             [Success.]
md1: unknown partition table
kjournald starting.  Commit interval 5 seconds
EXT3-fs (md1): using internal journal
EXT3-fs (md1): mounted filesystem with writeback data mode
PRODUCTID=0x00002025 PRODUCTID=0x00000000
** use initrd mode. **
--- rcStart (initrd) ---
mount: mounting proc on /proc failed: Device or resource busy
mount: mounting sysfs on /sys failed: Device or resource busy
Cannot set device ring parameters: Operation not supported
Cannot set device ring parameters: Operation not supported
Cannot set device ring parameters: Operation not supported
Cannot set device ring parameters: Operation not supported
Cannot get device ring settings: No such device
Cannot get device ring settings: No such device
Cannot get device ring settings: No such device
Cannot get device ring settings: No such device
=== checkroot.sh ===
grep: /var/tmp/devlink: No such file or directory
create_devlink:Using new routine.
grep: /var/tmp/devlink.bak: No such file or directory
Can't open /var/tmp/devlink.bak: No such file or directory.
Can't open /var/tmp/devlink.bak: No such file or directory.
md2: unknown partition table
Adding 999420k swap on /dev/md2.  Priority:-1 extents:1 across:999420k
create dir : /var/www
=== create_devlink.sh ===
create_devlink:Using new routine.
=== startSysMd.sh ===
-- rebuild mdadm.conf for BOOT, ROOTFS with Intelligent routine --
checkDiskStatus : disk1 plugged
checkDiskStatus : disk1 LibSys_IsScsiDeviceExist [1] 0:0:0:0
checkDiskStatus : disk2 plugged
checkDiskStatus : disk2 LibSys_IsScsiDeviceExist [1] 1:0:0:0
checkDiskPerformanceParallel : Waiting for performance check will be done(timeout=20).
checkDiskPerformanceParallel : Disk which has performance lower than 30 MB/s will be kicked out.
checkDiskPerformanceParallel : disk1 plugged
checkDiskPerformanceParallel : disk2 plugged
checkDiskPerformanceParallel : disk1 performans test ... 88918 kB/s [OK]
checkDiskPerformanceParallel : disk2 performans test ... 70414 kB/s [OK]
mount: mounting /dev/disk1_1 on /tmp/boot_test failed: Device or resource busy
mount: mounting /dev/disk2_1 on /tmp/boot_test failed: Device or resource busy
libmd: GetMdBaseDisk : Selected 0
mdadm: cannot open /dev/disk??_1: No such file or directory
mdadm: cannot open /dev/disk??_2: No such file or directory
mdadm: cannot open /dev/disk??_5: No such file or directory
mdadm main: failed to get exclusive lock on mapfile
-- setup max error counts --
/sys/block/md0/md/maxerr_cnt is setted to 1000
/sys/block/md1/md/maxerr_cnt is setted to 1000
/sys/block/md2/md/maxerr_cnt is setted to 1000
=== fwupdate.sh ===
umount: can't umount /boot: Invalid argument
mkdir: can't create directory '/boot': File exists
kjournald starting.  Commit interval 5 seconds
EXT3-fs (md0): using internal journal
EXT3-fs (md0): mounted filesystem with writeback data mode
ls: /boot/u-boot*.buffalo.updated: No such file or directory
fwupdate.sh:FW not updated
=== closeSysMd.sh ===
md0: detected capacity change from 1023868928 to 0
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
md: unbind<sdb1>
md: export_rdev(sdb1)
/sbin/hotplug [block]
/sbin/hotplug [block]
mdadm: stopped /dev/md0
/sbin/hotplug [block]
/sbin/hotplug [bdi]
md1: detected capacity change from 5114888192 to 0
md: md1 stopped.
md: unbind<sda2>
md: export_rdev(sda2)
md: unbind<sdb2>
md: export_rdev(sdb2)
/sbin/hotplug [block]
mdadm: stopped /dev/md1
mdadm: Cannot get exclusive access to /dev/md2:Perhaps a running process, mounted filesystem or active volume group?
=== sethostname.sh ===
/sbin/hotplug [bdi]
/sbin/hotplug [block]
/sbin/hotplug [block]
configure files from Buffalo parameters.
=== restore_config.sh ===
-- rebuild mdadm.conf for BOOT --
mdadm: cannot open /dev/disk??_1: No such file or directory
mdadm main: failed to get exclusive lock on mapfile
md: md0 stopped.
/sbin/hotplug [block]
md: bind<sdb1>
md: bind<sda1>
md/raid1:md0: active with 2 out of 2 mirrors
created bitmap (1 pages) for device md0
/sbin/hotplug [bdi]
md0: bitmap initialized from disk: read 1/1 pages, set 0 of 16 bits
/sbin/hotplug [block]
md0: detected capacity change from 0 to 1023868928
mdadm: /dev/md0 has been started with 2 drives.
-- setup max error counts --
/sbin/hotplug [block]
/sys/block/md0/md/maxerr_cnt is setted to 1000
md0: unknown partition table
kjournald starting.  Commit interval 5 seconds
EXT3-fs (md0): using internal journal
EXT3-fs (md0): mounted filesystem with writeback data mode
Restore previous configuration files
/tmp/etc/localtime ->
BusyBox v1.20.2 (2016-04-01 09:16:52 JST) multi-call binary.

Usage: dirname FILENAME

Strip non-directory suffix from FILENAME

BusyBox v1.20.2 (2016-04-01 09:16:52 JST) multi-call binary.

Usage: mkdir [OPTIONS] DIRECTORY...

Create DIRECTORY

        -m MODE Mode
        -p      No error if exists; make parent directories as needed

md0: detected capacity change from 1023868928 to 0
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
md: unbind<sdb1>
md: export_rdev(sdb1)
/sbin/hotplug [block]
mdadm: stopped /dev/md0
/sbin/hotplug [block]
/sbin/hotplug [bdi]
md: md1 stopped.
/sbin/hotplug [block]
/sbin/hotplug [block]
mdadm: stopped /dev/md1
mdadm: Cannot get exclusive access to /dev/md2:Perhaps a running process, mounted filesystem or active volume group?
/sbin/hotplug [bdi]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
grep: /etc/melco/iscsi_info: No such file or directory
Can't open /etc/melco/iscsi_info: No such file or directory.
=== EnablingAutoip.sh ===
=== networking.sh ===
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth1.pid eth1
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth0.pid eth0
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-bond0.pid bond0
/etc/init.d/networking.sh : Read dhcpc file
/etc/init.d/networking.sh : configure :
create network files.. (eth1)
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
create network files.. (eth0)
IP=[dhcp], netmask=[], dgw=[]
killall: dhcpcd: no process killed
/etc/init.d/networking.sh: line 91: /etc/init.d/networking.sh : Delete /etc/dhcpc/dhcpcd-.pid: No such file or directory
Configuration network interface: lo eth0 eth1
/sbin/ifconfig eth0 mtu 1500 multicast
/sbin/ifconfig eth1 mtu 1500 multicast
/sbin/ifconfig eth0  netmask
requesting DHCP  tout=30[s]
networking.sh: dhcp requesting...
SIOCGIFADDR :Cannot assign requested address
DontDownIfacepool #1: pkt_size=1536, buf_size=1632 - 256 of 256 buffers added

alwaysFork
eth1: link up
eth1: started
** eth1 : networking.sh dhcp fin.
Waiting 1748 ...sendto:  count 6   sync 1
sendto:  count 5   sync 0
sendto:  count 6   sync 0
dhcpInit call AutoipBound
setAutoIP eth1 called
MAC address = 10:6f:3f:XX:XX:XX
file name /etc/dhcpc/autoip-eth1.info
/sbin/ifconfig eth1 169.254.17.107 netmask 255.255.0.0 up
Arp result 0
/etc/init.d/rService
finished.
Checking network address for each network device
SIOCGIFADDR :No such device
networking.sh: arp_newip_notify_sub : Can't get ipaddr of eth0.
networking.sh: arp_newip_notify_sub : executing arping -A 169.254.17.107 -I eth1 -c 1
add default if
configure files from Buffalo parameters.
=== syslog.sh ===
could not find all syslogger daemons
=== kernelmon.sh ===
Starting kernelmon:=== miconmon.sh ===
KERNELMOn (SATA 0 plugged)
KERNELMOn (SATA 1 plugged)
err: RecvPacket: readlen=0.
err: RecvPacket: readlen=0.
/etc/init.d/miconmon.sh: line 86: [: -ne: unary operator expected
=== usb.sh ===
eth1: link down
KERNELMOn (lanact 0 half eth1)
eth1: link up, full duplex, speed 1 Gbps
KERNELMOn (lanact 1000 full eth1)
/sbin/hotplug [module]
/sbin/hotplug [bus]
usbcore: registered new interface driver usbfs
/sbin/hotplug [class]
usbcore: registered new interface driver hub
/sbin/hotplug [drivers]
usbcore: registered new device driver usb
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
xhci_hcd 0000:00:01.0: xHCI Host Controller
xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 1
xhci_hcd 0000:00:01.0: irq 58, io mem 0xe0000000
/sbin/hotplug [module]
/sbin/hotplug [usb]
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
xhci_hcd 0000:00:01.0: xHCI Host Controller
xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
/sbin/hotplug [usb]
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
/sbin/hotplug [usb]
/sbin/hotplug [usb]
/sbin/hotplug [usb_device]
/sbin/hotplug [usb_device]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.0: Marvell Orion EHCI
ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 3
/sbin/hotplug [module]
/sbin/hotplug [drivers]
ehci_marvell ehci_marvell.0: irq 45, io base 0xfbb50100
ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
/sbin/hotplug [usb]
/sbin/hotplug [usb]
/sbin/hotplug [drivers]
/sbin/hotplug [usb_device]
/sbin/hotplug [drivers]
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
/sbin/hotplug [module]
/sbin/hotplug [drivers]
Initializing USB Mass Storage driver...
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
/sbin/hotplug [drivers]
/sbin/hotplug [module]
grep: /etc/melco/usbshareinfo: No such file or directory
/usr/local/lib/libsys: line 1211: sqlite3: command not found
/usr/local/lib/libsys: line 1236: sqlite3: command not found
/usr/local/lib/libsys: line 1248: sqlite3: command not found
=== clientUtil_servd.sh ===
Starting clientUtil_server:
  ->Starting on eth0
  ->Starting on eth1
=== daemonwatch.sh ===
=== bootcomplete.sh ===
No need to run drivecheck.sh
cat: can't open '/tmp/lcd_status': No such file or directory
cat: can't open '/tmp/lcd_status': No such file or directory
err: RecvPacket: readlen=0.
/usr/local/bin/hdd_raid_syncspeed.sh: line 147: /sys/block/md0/md/sync_speed_max: No such file or directory
/usr/local/bin/hdd_raid_syncspeed.sh: line 147: /sys/block/md1/md/sync_speed_max: No such file or directory
hdd_raid_syncspeed.sh: Adding EDP md devices
hdd_raid_syncspeed.sh: USERLAND_MD=md10 md11 md12 md13 md14 md101 md102
=== micon_setup.sh ===
^C=== late_inspection_phase.sh ===
=== buffalo_rescue.sh ===
buffalo_rescue.sh: Its not a nand boot environment.
buffalo_rescue.sh: Its not a usb boot environment.

BUFFALO INC. LinkStation series
LS421DE-EM34C login:




Bild


Zuletzt geändert von Antonas am Mo 20. Feb 2017, 08:58, insgesamt 1-mal geändert.



Mo 20. Feb 2017, 08:56
Profil
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 7 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
oxygen8,

Please check the latest bootlog kernel for the presence of critical errors

maybe can flash the firmware without this option?

Bild

ACP_Commander work fine too
Bild


Mo 20. Feb 2017, 09:10
Profil
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 7 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
I flashed firmware without parameter "BOOT Update", but he cycle

Bild

information via Serial Console

Code:
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again
ubiformat: continue? (y/N) failed to read prompt; assuming 'no'
unknown response; please try again


while he rewrote u-boot :?

f@@king Buffalo :evil: .... I forcedly return to ls421 :?


Mo 20. Feb 2017, 10:22
Profil
Beiträge der letzten Zeit anzeigen:  Sortiere nach  

Ein neues Thema erstellen Auf das Thema antworten  [ 126 Beiträge ]  Gehe zu Seite Vorherige  1 ... 9, 10, 11, 12, 13





Suche nach:

Ähnliche Beiträge

LS420D Festplattenwahl
Forum: Buffalo Linkstation Pro/Live
Autor: oxygen8
Antworten: 3
LS420D - ein paar Anfängerfragen
Forum: Buffalo Linkstation Pro Duo
Autor: phantom
Antworten: 10
Debian auf LS420D (LS420D91E)
Forum: Buffalo Linkstation Duo
Autor: mamphp
Antworten: 4
Benchmark LS420D Raid 0
Forum: Buffalo Linkstation Pro Duo
Autor: oxygen8
Antworten: 0
LS420D findet externe HDD nicht
Forum: Buffalo Linkstation Pro Duo
Autor: The Reemt
Antworten: 4

Wer ist online?

Mitglieder in diesem Forum: Exabot [Bot] und 8 Gäste


Deine Berechtigungen

 Du darfst keine neuen Themen in diesem Forum erstellen.
 Du darfst keine Antworten zu Themen in diesem Forum erstellen.
 Du darfst deine Beiträge in diesem Forum nicht ändern.
 Du darfst deine Beiträge in diesem Forum nicht löschen.
 Du darfst keine Dateianhänge in diesem Forum erstellen.

Gehe zu:  


| NAS-Hilfe.de - die deutsche Buffalo NAS-Hilfe Seite | Mein Blog - Bloggen Querbeet... | Powered by phpBB © phpBB Group. | Deutsche Übersetzung durch phpBB.de | Impressum |