Aktuelle Zeit: Do 27. Jul 2017, 02:33



Ein neues Thema erstellen Auf das Thema antworten  [ 126 Beiträge ]  Gehe zu Seite Vorherige  1 ... 8, 9, 10, 11, 12, 13  Nächste
 LS420D zur TS1200D umflashen 
Autor Nachricht
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 8 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
oxygen8 hat geschrieben:
Zitat:
Unknown command 'reboot=cold,hard' - try 'help'


remove the wrong commands



Creating 1 MTD partitions on "nand0":
0x000000000000-0x000002000000 : "mtd=0"
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: Bad block at 0x000001c40000
nand_read_bbt: Bad block at 0x000001c60000
nand_read_bbt: Bad block at 0x000003fa0000
nand_read_bbt: Bad block at 0x000006080000
nand_read_bbt: Bad block at 0x0000060a0000
nand_read_bbt: Bad block at 0x000008ac0000
nand_read_bbt: Bad block at 0x00000b800000
nand_read_bbt: Bad block at 0x00000efa0000
nand_read_bbt: Bad block at 0x00001a480000
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=0"
UBI: MTD device size: 32 MiB
UBI: number of good PEBs: 254
UBI: number of bad PEBs: 2
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 254
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 3/1
UBIFS: mounted UBI device 0, volume 1, name "boot"
UBIFS: mounted read-only
UBIFS: file system size: 30347264 bytes (29636 KiB, 28 MiB, 239 LEBs)
UBIFS: journal size: 1523712 bytes (1488 KiB, 1 MiB, 12 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 1499787 bytes (1464 KiB)
Loading file '/uImage.buffalo' to addr 0x01200000 with size 2905032 (0x002c53c8)...
Done
Loading file '/initrd.buffalo' to addr 0x02600000 with size 11911739 (0x00b5c23b)...
Done
No SPI flash selected. Please run `sf probe'
Unknown command 'reboot=cold,hard' - try 'help'
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found

** Invalid boot device **

** Invalid boot device **

** Invalid boot device **

** Invalid boot device **
No SPI flash selected. Please run `sf probe'
Unknown command 'reboot=cold,hard' - try 'help'
*** booting failed. press func sw to continue

egiga1 wait for link .Done - link up.
Using egiga1 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'uImage.buffalo'.
Load address: 0x1200000
Loading: #################################################################
#################################################################
#################################################################
###
done
Bytes transferred = 2894432 (2c2a60 hex)
Using egiga1 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'initrd.buffalo'.
Load address: 0x2600000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
######################################
done
Bytes transferred = 12001020 (b71efc hex)
No SPI flash selected. Please run `sf probe'
Unknown command 'reboot=cold,hard' - try 'help'
BUFFALO>> setenv bootcommon 'setenv bootargs $console $bootargs_root $bootargs_func $buffalo_ver $uboot_date $mtdparts $bootsystem; ;sf protect off; bootm 0x1200000 0x2600000'


Sa 28. Jan 2017, 16:44
Profil
Dieser Werbeblock wird nur bei Gästen angezeigt
Online
Globaler Moderator

Registriert: Mo 5. Apr 2010, 23:32
Beiträge: 6214
Bilder: 333

Bedankte sich: 173 mal
Erhielt: 799 Danksagungen in 739 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
Du hast den bootloader verändert.
Damit kenne ich mich nicht aus.

Die Linkstation läd zwar dei Dateien, startet aber dann aus dem Flash.


bootorder=nand usb fail tftp

kanst du das ändern in

bootorder=tftp nand usb fail


Sa 28. Jan 2017, 18:31
Profil Persönliches Album 
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 8 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
oxygen8 hat geschrieben:
Du hast den bootloader verändert.
Damit kenne ich mich nicht aus.

Die Linkstation läd zwar dei Dateien, startet aber dann aus dem Flash.


bootorder=nand usb fail tftp

kanst du das ändern in

bootorder=tftp nand usb fail


BootROM 1.08
Booting from SPI flash


General initialization - Version: 1.0.0
mvBoardSerdesModulesScan: mvTwsiRead error, Using default serdes configuration ****
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x67100
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1

DDR3 Training Sequence - Run DDR3 at 600 Mhz

########### LOG LEVEL 1 (D-UNIT SETUP)###########

Static D-UNIT Setup:
0x00001400 = 0x73014924
0x00001404 = 0x3000B808
0x00001408 = 0x56159996
0x0000140C = 0x3AD93F96
0x00001410 = 0x120F0000
0x00001414 = 0x00000000
0x00001418 = 0x00000E00
0x0000141C = 0x00000642
0x00001420 = 0x00000004
0x00001424 = 0x0100F37F
0x00001428 = 0x000F8830
0x00001454 = 0x00000000
0x00001474 = 0x00000000
0x0000142C = 0x014C4EE4
0x0000147C = 0x0000C671
0x00001494 = 0x00010000
0x00001498 = 0x00000000
0x0000149C = 0x0000030F
DDR3 Training Sequence - Run without PBS.
Cuurrent frequency is: 100MHz
Cuurrent frequency is: 444MHz
DDR3 - Write Leveling - Starting HW WL procedure
DDR3 - Write Leveling - Write Leveling Cs - 0 Results:
DDR3 - Write Leveling - PUP: 0, Phase: 0, Delay: 03
DDR3 - Write Leveling - PUP: 1, Phase: 0, Delay: 07
DDR3 - Write Leveling - HW WL Ended Successfully
DDR3 - Read Leveling - Starting HW RL procedure
DDR3 - Read Leveling - Results for CS - 0
DDR3 - Read Leveling - PUP: 0, Phase: 2, Delay: 00
DDR3 - Read Leveling - PUP: 1, Phase: 2, Delay: 02
DDR3 - Read Leveling - Read Sample Delay: 09
DDR3 - Read Leveling - Read Ready Delay: 0D
DDR3 - Read Leveling - HW RL Ended Successfully
DDR3 - Write Leveling Hi-Freq Supplement - Starting
DDR3 - Write Leveling Hi-Freq Supplement - SW Override Enabled
COUNT = 0
DATA PUP:
04030201 08070605 0C0B0A09 100F0E0D
14131211 18171615 1C1B1A19 201F1E1D
24232221 28272625 2C2B2A29 302F2E2D
34333231 38373635 3C3B3A39 403F3E3D
44434241 48474645 4C4B4A49 504F4E4D
54535251 58575655 5C5B5A59 605F5E5D
64636261 68676665 6C6B6A69 706F6E6D
74737271 78777675 7C7B7A79 807F7E7D
CS: 0 PUP: 0
Actual Data = 21
Expected Data = 21
uiError = 00
uiErrorN = 00

CS: 0 PUP: 1
Actual Data = 22
Expected Data = 22
uiError = 00
uiErrorN = 00
COUNT = 1
DATA PUP:
04030201 08070605 0C0B0A09 100F0E0D
14131211 18171615 1C1B1A19 201F1E1D
24232221 28272625 2C2B2A29 302F2E2D
34333231 38373635 3C3B3A39 403F3E3D
44434241 48474645 4C4B4A49 504F4E4D
54535251 58575655 5C5B5A59 605F5E5D
64636261 68676665 6C6B6A69 706F6E6D
74737271 78777675 7C7B7A79 807F7E7D
CS: 0 PUP: 0
Actual Data = 21
Expected Data = 21
uiError = 00
uiErrorN = 00

CS: 0 PUP: 1
Actual Data = 22
Expected Data = 22
uiError = 00
uiErrorN = 00
DDR3 - Write Leveling Hi-Freq Supplement - Ended Successfully

########## LOG LEVEL 3(Windows margins per-DQ) ##########
DDR3 - RX CS: 0

DATA RESULTS:

BYTE:0
DQ's LOW HIGH WIN-SIZE
============================================
DQ[ 0] 0x41 0x2D 0xED
DQ[ 1] 0x33 0x2F 0xFD
DQ[ 2] 0xEA 0x4B 0x62
DQ[ 3] 0x01 0xFA 0xFA
DQ[ 4] 0x59 0xFE 0xA6
DQ[ 5] 0x9A 0xE5 0x4C
DQ[ 6] 0x6F 0xFF 0x91
DQ[ 7] 0x3B 0xAD 0x73

BYTE:1
DQ's LOW HIGH WIN-SIZE
============================================
DQ[ 8] 0x5D 0x9E 0x42
DQ[ 9] 0x4E 0x0D 0xC0
DQ[10] 0xC7 0x71 0xAB
DQ[11] 0x41 0xFF 0xBF
DQ[12] 0xE2 0x40 0x5F
DQ[13] 0x7A 0x86 0x0D
DQ[14] 0xFA 0xE7 0xEE
DQ[15] 0x20 0x08 0xE9


############ LOG LEVEL 2(Windows margins) ############
DDR3 - DQS RX - Set Dqs Centralization Results - CS: 0

DQS LOW HIGH WIN-SIZE Set
==============================================
0 0x00 0x1A 0x1A 0x0D
1 0x00 0x1B 0x1B 0x0D

########## LOG LEVEL 3(Windows margins per-DQ) ##########
DDR3 - TX CS: 0

DATA RESULTS:

BYTE:0
DQ's LOW HIGH WIN-SIZE
============================================
DQ[ 0] 0x2E 0x41 0x13
DQ[ 1] 0x30 0x33 0x03
DQ[ 2] 0x4C 0xEA 0x9E
DQ[ 3] 0xFB 0x01 0x06
DQ[ 4] 0xFF 0x59 0x5A
DQ[ 5] 0xE6 0x9A 0xB4
DQ[ 6] 0x00 0x6F 0x6F
DQ[ 7] 0xAE 0x3B 0x8D

BYTE:1
DQ's LOW HIGH WIN-SIZE
============================================
DQ[ 8] 0x9F 0x5D 0xBE
DQ[ 9] 0x0E 0x4E 0x40
DQ[10] 0x72 0xC7 0x55
DQ[11] 0x00 0x41 0x41
DQ[12] 0x41 0xE2 0xA1
DQ[13] 0x87 0x7A 0xF3
DQ[14] 0xE8 0xFA 0x12
DQ[15] 0x09 0x20 0x17


############ LOG LEVEL 2(Windows margins) ############
DDR3 - DQS TX - Set Dqs Centralization Results - CS: 0

DQS LOW HIGH WIN-SIZE Set
==============================================
0 0x00 0x1B 0x1B 0x0D
1 0x00 0x1B 0x1B 0x0D
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED

____ _
| __ ) _ _ ___ ___ ___ | | ___
| _ \| | | |/ | / | / _ \| | / _ \
| |_) || |_| || __|| __| (_) || || (_) |
|____/ \___/ |_| |_| \__/|||_| \___/
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \/ _ \| __|
| |_| |___| |_) || (_) | (_) || |_
\___/ |____/ \___/ \___/ \__|
** LOADER **


U-Boot 2011.12 (Jan 15 2015 - 21:22:47) Marvell version: v2011.12 2014_T2.0p1

Board: YANAGI
BoardID= 0
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
PHY ID = 1d
PHY ID = 1d

Map: Code: 0x1ff0d000:0x1ffa2b68
BSS: 0x1ffefaa4
Stack: 0x1f9fcef8
Heap: 0x1f9fd000:0x1ff0d000

NAND: 512 MiB
MMC: MRVL_MMC: 0
SF: Detected MX25L8005 with page size 64 KiB, total 1 MiB

Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 1.1
PEX 0.1(1): Detected No Link.
u-boot envinit tval=f24c7633
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
USB Power ON

Marvell Serial ATA Adapter
Integrated Sata device found

MAC Address : 10:6F:3F:xx:xx:xx
Net: egiga0, egiga1 [PRIME]
hit any key to switch tftp boot.
Hit any key to stop autoboot: 0
switched to TFTP boot.
Hit any key to stop autoboot: 0
BUFFALO>> setenv bootorder 'tftp nand usb fail'
BUFFALO>> boot
egiga1 wait for link .Done - link up.
Using egiga1 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'uImage.buffalo'.
Load address: 0x1200000
Loading: #################################################################
#################################################################
#################################################################
###
done
Bytes transferred = 2894432 (2c2a60 hex)
Using egiga1 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'initrd.buffalo'.
Load address: 0x2600000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
######################################
done
Bytes transferred = 12001020 (b71efc hex)
No SPI flash selected. Please run `sf probe'
## Booting kernel from Legacy Image at 01200000 ...
Image Name: Linux-3.3.4
Created: 2013-10-28 7:16:53 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2894368 Bytes = 2.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02600000 ...
Image Name: initrd
Created: 2017-01-28 4:21:27 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 12000956 Bytes = 11.4 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...


Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0
Initializing cgroup subsys cpu
Linux version 3.3.4 (m-ikebukuro@debian-m-ikebukuro) (gcc version 4.6.2 (Linaro GCC branch-4.6.2. Marvell GCC 201201-883.01c949de) ) #1 Mon Oct 28 16:16:49 JST 2013
CPU: Marvell PJ4Bv7 Processor [561f5811] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
Machine: Marvell Armada-370
Using UBoot passing parameters structure
>>>>>>>Tag MAC 76:33:4c:xx:xx:xx
>>>>>>>Tag MAC 4c:13:cd:xx:xx:xx
Memory policy: ECC disabled, Data cache writealloc
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/nfs rw BOOTVER=0.16 UBOOT_DATE=2015/01/15 mtdparts=armada-nand:0x2000000(boot),0x1e000000(rootfs) tftpboot=yes
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 498028k/498028k available, 26260k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc053383c (5295 kB)
.init : 0xc0534000 - 0xc0559000 ( 148 kB)
.data : 0xc055a000 - 0xc0589840 ( 191 kB)
.bss : 0xc0589864 - 0xc05c2350 ( 227 kB)
NR_IRQS:256
axp_time_init
Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
hw perfevents: no hardware support available
Setting up static identity map for 0x3da858 - 0x3da89c
devtmpfs: initialized
xor: measuring software checksum speed
arm4regs : 1151.600 MB/sec
8regs : 817.200 MB/sec
32regs : 1149.600 MB/sec
xor: using function: arm4regs (1151.600 MB/sec)
NET: Registered protocol family 16
L0 cache Enabled
Speculative Prefetch Disabled
aurora_l2_init
Aurora: Enabling L2
AuroraL2: System L2 cache support initialised
Support IO coherency.
Enable DLB and DRAM write coalescing

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 512MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
DEVICE_CS0 ....base f2000000, size 32MB
DEVICE_CS1 ....no such
DEVICE_CS2 ....no such
DEVICE_CS3 ....no such
PEX0_MEM ....base e0000000, size 32MB
PEX0_IO ....base f1100000, size 1MB
PEX1_MEM ....base e2000000, size 32MB
PEX1_IO ....base f1200000, size 1MB
INTER_REGS ....base d0000000, size 1MB
DMA_UART ....no such
SPI_CS0 ....base f0000000, size 16MB
SPI_CS1 ....no such
SPI_CS2 ....no such
SPI_CS3 ....no such
SPI_CS4 ....no such
SPI_CS5 ....no such
SPI_CS6 ....no such
SPI_CS7 ....no such
BOOT_ROM_CS ....no such
DEV_BOOTCS ....base f5000000, size 16MB
PMU_SCRATCHPAD ....no such
CRYPT0_ENG ....base c8010000, size 64KB

Marvell Armada370 Board-- YANAGI Soc: MV6710 A1 LE
LSP version: Armada370_LSP_3.1.0_p15_NQ


Detected Tclk 200000000, SysClk 600000000, FabricClk 600000000
gpiochip_add: registered GPIOs 0 to 64 on device: mv_gpio
hw-breakpoint: debug architecture 0x4 unsupported.
Marvell USB EHCI Host controller #0: d004c400
Marvell USB EHCI Host controller #1: d004c200
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe1ffffff]
PCI: bus0: Fast back to back transfers disabled
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io 0x100000-0x1fffff]
pci_bus 0000:01: root bus resource [mem 0xe2000000-0xe3ffffff]
PCI: bus1: Fast back to back transfers enabled
pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit]
bio: create slab <bio-0> at 0
raid6: int32x1 135 MB/s
raid6: int32x2 210 MB/s
raid6: int32x4 203 MB/s
raid6: int32x8 244 MB/s
raid6: using algorithm int32x8 (244 MB/s)
vgaarb: loaded
SCSI subsystem initialized
Switching to clocksource armada370_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 11716K
cesadev_init(c053bb7c)
mvCesaInit: channels=1, session=640, queue=64
Armada XP hwmon thermal sensor initialized.
Initializing Armada-XP CPU power management (DISABLED)
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
initial_polarity_val = 0x0001f800
initial_polarity_val_high = 0x00000000
Buffalo GPIO SATA Hotplug Event Driver (C) BUFFALO INC. Ver.1.00 installed.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 995
async_tx: api initialized (async)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Initializing ths8200_init
Initializing dove_adi9889_init
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor )
mv_xor mv_xor.1: Marvell XOR: ( xor )
mv_xor mv_xor.2: Marvell XOR: ( cpy )
mv_xor mv_xor.3: Marvell XOR: ( fill cpy )
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xd0012000 (irq = 41) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
** BUFFALO Disable Command Queuing Function [sata_mv sata_mv.0] **
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 55
ata2: SATA max UDMA/133 irq 55
SPI Serial flash detected @ 0xf0000000, 1024KB (16sec x 64KB)
armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: bad block at 0x000001c40000
nand_read_bbt: bad block at 0x000001c60000
nand_read_bbt: bad block at 0x000003fa0000
nand_read_bbt: bad block at 0x000006080000
nand_read_bbt: bad block at 0x0000060a0000
nand_read_bbt: bad block at 0x000008ac0000
nand_read_bbt: bad block at 0x00000b800000
nand_read_bbt: bad block at 0x00000efa0000
nand_read_bbt: bad block at 0x00001a480000
2 cmdlinepart partitions found on MTD device armada-nand
Creating 2 MTD partitions on "armada-nand":
0x000000000000-0x000002000000 : "boot"
0x000002000000-0x000020000000 : "rootfs"
mv_eth_probe: port_mask=0x3, cpu_mask=0x1
0 - Base 0x00000000 , Size = 0x20000000.
4 - Base 0xf2000000 , Size = 0x02000000.
8 - Base 0xe0000000 , Size = 0x02000000.
9 - Base 0xf1100000 , Size = 0x00100000.
10 - Base 0xe2000000 , Size = 0x02000000.
11 - Base 0xf1200000 , Size = 0x00100000.
12 - Base 0xd0000000 , Size = 0x00100000.
14 - Base 0xf0000000 , Size = 0x01000000.
23 - Base 0xf5000000 , Size = 0x01000000.
25 - Base 0xc8010000 , Size = 0x00010000.
o 2 Giga ports supported
o NETA acceleration mode 1
o RX Queue support: 1 Queues * 128 Descriptors
o TX Queue support: 1 Queues * 512 Descriptors
o GSO supported
o GRO supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Driver ERROR statistics enabled
o Switch support enabled

o Loading network interface(s)

o Port 0 is connected to Linux netdevice
giga p=0: mtu=1500, mac=d002beec
o eth0, ifindex = 2, GbE port = 0

o Port 1 is connected to Linux netdevice
giga p=1: mtu=1500, mac=d002beec
o eth1, ifindex = 3, GbE port = 1

sky2: driver version 1.30
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
cpuidle: using governor ladder
cpuidle: using governor menu
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
TCP cubic registered
NET: Registered protocol family 17
VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
rtc-rs5c372 0-0032: setting system clock to 2007-10-31 16:32:33 UTC (1193848353)
ata1: SATA link down (SStatus 0 SControl F300)
ata2: SATA link down (SStatus 0 SControl F300)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
FAT-fs (ram0): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT-fs (ram0): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
List of all partitions:
1f00 1024 mtdblock0 (driver?)
1f01 32768 mtdblock1 (driver?)
1f02 491520 mtdblock2 (driver?)
No filesystem could mount root, tried: ext3 ext2 ext4 vfat msdos hfsplus fuseblk xfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,255)
[<c0013d80>] (unwind_backtrace+0x0/0xe4) from [<c03d4a60>] (panic+0x6c/0x1a4)
[<c03d4a60>] (panic+0x6c/0x1a4) from [<c0534bd0>] (mount_block_root+0x1d0/0x218)
[<c0534bd0>] (mount_block_root+0x1d0/0x218) from [<c0535800>] (initrd_load+0xa8/0x318)
[<c0535800>] (initrd_load+0xa8/0x318) from [<c0534ec8>] (prepare_namespace+0xc4/0x1c0)
[<c0534ec8>] (prepare_namespace+0xc4/0x1c0) from [<c053483c>] (kernel_init+0xec/0x118)
[<c053483c>] (kernel_init+0xec/0x118) from [<c000f18c>] (kernel_thread_exit+0x0/0x8)


on this spot stopped. turn off the power?

UPD After 10 minutes of waiting, turn off the power, power on - PID 00002026


Sa 28. Jan 2017, 19:00
Profil
Online
Globaler Moderator

Registriert: Mo 5. Apr 2010, 23:32
Beiträge: 6214
Bilder: 333

Bedankte sich: 173 mal
Erhielt: 799 Danksagungen in 739 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
Zitat:
No SPI flash selected. Please run `sf probe'
## Booting kernel from Legacy Image at 01200000 ...



run

Code:
sf probe


Sa 28. Jan 2017, 19:21
Profil Persönliches Album 
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 8 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
how to do it? bootload does not stop

BUFFALO>>sf probe instead boot ?


Sa 28. Jan 2017, 19:52
Profil
Online
Globaler Moderator

Registriert: Mo 5. Apr 2010, 23:32
Beiträge: 6214
Bilder: 333

Bedankte sich: 173 mal
Erhielt: 799 Danksagungen in 739 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
i do not know
try it


Sa 28. Jan 2017, 21:31
Profil Persönliches Album 
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 8 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
oxygen8 hat geschrieben:
i do not know
try it

Code:
BUFFALO>> sf probe
sf - SPI flash sub-system

Usage:
sf probe [bus:]cs [hz] [mode]   - init flash device on given SPI bus
                                  and chip select
sf read addr offset len         - read `len' bytes starting at
                                  `offset' to memory at `addr'
sf write addr offset len        - write `len' bytes from memory
                                  at `addr' to flash at `offset'
sf erase offset [+]len          - erase `len' bytes from `offset'
                                  `+len' round up `len' to block size
sf update addr offset len       - erase and write `len' bytes from memory
                                  at `addr' to flash at `offset'
BUFFALO>>
:?


So 29. Jan 2017, 09:30
Profil
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 8 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
oxygen8,

may be install OpenWrt or Debian and therefrom correct PID under root? For installation these systems is critical PID?


So 29. Jan 2017, 10:51
Profil
Online
Globaler Moderator

Registriert: Mo 5. Apr 2010, 23:32
Beiträge: 6214
Bilder: 333

Bedankte sich: 173 mal
Erhielt: 799 Danksagungen in 739 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
Ich habe mich damit nicht beschäftigt.
Versuche es einfach.


So 29. Jan 2017, 15:10
Profil Persönliches Album 
Foren-Mitglied
Foren-Mitglied

Registriert: Sa 29. Okt 2016, 10:17
Beiträge: 67


Bedankte sich: 8 mal
Erhielt: 0 Danksagungen in 0 Beiträgen

Bedanke dich für den Beitrag 
Beitrag Re: LS420D zur TS1200D umflashen
oxygen8 hat geschrieben:
Ich habe mich damit nicht beschäftigt.
Versuche es einfach.


in my situation which OS is easier to install??


So 29. Jan 2017, 15:29
Profil
Beiträge der letzten Zeit anzeigen:  Sortiere nach  

Ein neues Thema erstellen Auf das Thema antworten  [ 126 Beiträge ]  Gehe zu Seite Vorherige  1 ... 8, 9, 10, 11, 12, 13  Nächste





Suche nach:

Ähnliche Beiträge

LS420D Festplattenwahl
Forum: Buffalo Linkstation Pro/Live
Autor: oxygen8
Antworten: 3
LS420D - ein paar Anfängerfragen
Forum: Buffalo Linkstation Pro Duo
Autor: phantom
Antworten: 10
Debian auf LS420D (LS420D91E)
Forum: Buffalo Linkstation Duo
Autor: mamphp
Antworten: 4
Benchmark LS420D Raid 0
Forum: Buffalo Linkstation Pro Duo
Autor: oxygen8
Antworten: 0
LS420D findet externe HDD nicht
Forum: Buffalo Linkstation Pro Duo
Autor: The Reemt
Antworten: 4

Wer ist online?

Mitglieder in diesem Forum: Google Adsense [Bot] und 10 Gäste


Deine Berechtigungen

 Du darfst keine neuen Themen in diesem Forum erstellen.
 Du darfst keine Antworten zu Themen in diesem Forum erstellen.
 Du darfst deine Beiträge in diesem Forum nicht ändern.
 Du darfst deine Beiträge in diesem Forum nicht löschen.
 Du darfst keine Dateianhänge in diesem Forum erstellen.

Gehe zu:  


cron
| NAS-Hilfe.de - die deutsche Buffalo NAS-Hilfe Seite | Mein Blog - Bloggen Querbeet... | Powered by phpBB © phpBB Group. | Deutsche Übersetzung durch phpBB.de | Impressum |